Your layout decides East Hartford's permit route
In an April 2025 update, East Hartford's Department of Permits and Inspections, at 740 Main Street, said it is accepting SolarAPP+ applications and individually processing other solar applications.
SolarAPP+ is an online plan check for standard home solar systems. A design that passes receives an Approval ID. In East Hartford, that approval is uploaded to OpenGov, the town's online permit portal, and the permit is issued instantly. For a one- or two-family home, both routes start in the same OpenGov category: "Solar - Residential 1&2 Family (and SolarAPP+)".
The same town page lists three exclusions: "Properties in the Historic District, in FEMA Flood Zones or projects which include structural reinforcements are NOT eligible to utilize SolarAPP+."
Two of those facts belong to your address. The third belongs to the layout, so two layouts on the same house can take two routes. Structural reinforcement means strengthening rafters or other framing so the roof can carry the panels. A modest array on one sound roof face may need none. A larger array that spreads onto a weaker section, such as an addition, may need it, and that layout then goes to individual review.
| Route | When it applies | Permits | How the permit is issued |
|---|---|---|---|
| SolarAPP+ | New rooftop system on a detached 1–2 family home, townhome or accessory structure, up to 38.4 kW, no structural reinforcement, outside the Historic District and FEMA flood zones | Electrical permit | Instantly, when the SolarAPP+ approval is uploaded to OpenGov |
| Individual review | Any layout with reinforcement, or any layout on a property in the Historic District or a flood zone | Electrical permit, plus a building permit if there are structural upgrades | After the department reviews the submitted plans |
For individual review, the town's residential PV permit procedure (a December 2023 PDF) lists the attachments: a one-line electrical diagram, a site plan with module attachment details, module and inverter spec sheets, copies of the contractor's E-1 (electrical contractor) licence and HIC (Home Improvement Contractor) registration, and a workers' compensation certificate. The procedure called processing "typically" two to three days and noted the 30 days state law allows. That is the town's 2023 description, not a promise.
Ground and pole mounts are a different path: they add zoning setback review, a sanitarian sign-off where there is a septic system, and engineering review near wetlands. Homes with three or more units use a separate application.
What to ask: which route does each layout take, and why? If the answer is SolarAPP+, ask for the Approval ID once it is issued. If it isn't, ask which of the three exclusions applies.
Check the historic district and flood map before you pick a roof face
Your address settles two route facts before anyone draws a panel. If either applies, both layouts go to individual review, and reinforcement only decides whether a building permit is added.
Historic district. East Hartford has a Historic District Commission, set up under a 1986 town ordinance. A Certificate of Appropriateness is the commission's written approval for a change inside a local historic district. Applications go electronically to the town's Grants Manager, and the commission meets on the second Tuesday of the month when it has business. This guide could not confirm which streets the district covers, so ask rather than guess.
Flood zone. A FEMA flood zone is an area the Federal Emergency Management Agency maps as flood-prone. A UConn Resilient Connecticut profile says the broad flood zones of the Connecticut River cover a portion of southwest East Hartford. That is a regional finding. Your parcel is a separate question.
How to settle both before the site visit:
- Look up your parcel in the town's GIS property viewer, which shows FEMA flood zones, or in FEMA's Flood Map Service Center.
- Contact the Grants Manager, who receives the commission's applications, and ask whether your address is in a local historic district.
- Give both answers to every installer you talk to.
- If either answer is yes, expect individual review for both layouts, and ask how each layout would be presented to the town.
An installer who checks for you should name the source. "It should be fine" is not an answer.
What each layout sheet would show
Proposed service: Wethersfield Solar is a proposed residential solar service. Its two-layout comparison would draw two layouts for the same house and price each on its own sheet. Coverage of East Hartford is proposed and not yet confirmed.
In East Hartford, the two layouts would line up with the town's rule. Layout A would usually be the simpler option, drawn to avoid reinforcement so it can stay on SolarAPP+ if the address allows. Layout B would be the higher-output option, even when it needs framing work and individual review. Both would use the same panel model, usage history and production method, so the differences come from the roof, not from changed assumptions.
Each layout sheet would show:
- A to-scale drawing with panel positions, the conduit route and the inverter location.
- Panel count and kW DC, the panels' combined rated output. For example, sixteen 400-watt panels make 6.4 kW DC.
- Estimated production in kWh per year, with the shade loss assumed for each roof face.
- Price and price per watt, meaning the price divided by the DC watts, which lets you compare quotes of different sizes.
- The East Hartford permit route, either SolarAPP+ or individual review, with the reason.
- Structural work as its own price line, so you can see what reinforcement adds.
- A solar-only price per watt, with reinforcement, roof work and any panel upgrade taken out.
- An Eversource tariff estimate for Buy-All and Netting, with the town's distressed-municipality adder shown separately.
- An itemized scope listing equipment models, electrical work, permit and utility fees, inspection, and what is excluded.
To prepare, gather 12 months of Eversource bills (the kWh figures matter most), the roof's age, attic access and any roof or electrical work you already plan. After you choose, the proposed service would handle that layout's permit, installation, inspection and Eversource application. It would not promise savings, approvals or timelines.
Worked example: one house, two routes
Illustrative example (Proposed service). One East Hartford house, two layouts. Same 400 W panel model and the same 12 months of usage. Production uses EcoGen's Connecticut reference of 1,294 kWh per kW per year, a statewide figure before shade and not a site estimate. Every price, fee and kWh figure below is an illustrative calculation, not a quote.
| Illustrative calculation | Layout A: main roof, rear face | Layout B: rear face plus rear addition |
|---|---|---|
| Panels and DC size | 16 × 400 W = 6.4 kW | 24 × 400 W = 9.6 kW |
| Structural work (illustrative) | None found at the site visit | Addition rafters need reinforcement, per an engineer |
| East Hartford permit route | SolarAPP+, if the address is outside the Historic District and flood zones | Individual review: electrical permit plus building permit |
| Permit-fee valuation at the town's $3.50/W | $22,400 → about $351–$360 | $33,600 → about $519–$525 |
| Illustrative quote | $18,560 | $29,760, including $2,400 reinforcement |
| Total price per watt | $2.90/W | $3.10/W |
| Solar-only price per watt | $2.90/W | $27,360 ÷ 9,600 W = $2.85/W |
| Against the $2.80/W state benchmark (band $2.46–$3.14) | +3.6%, inside the band | +1.8%, inside the band |
| Shade loss assumed per face | Not applied here; a real sheet states it | Not applied here; a real sheet states it |
| Production before shade | ≈ 8,282 kWh/yr | ≈ 12,422 kWh/yr |
| Year-1 Buy-All payment at $0.3289 + $0.0275 adder = $0.3564/kWh | ≈ $2,952 (adder ≈ $228) | ≈ $4,427 (adder ≈ $342) |
Layout B looks more expensive per watt: $3.10 against $2.90. Take the reinforcement out and B is the cheaper array per watt, at $2.85. The difference is framing work, not overpriced panels, which is why the structural line must be priced on its own.
So price per watt does not settle this choice. Layout B produces about 50% more before shade. In exchange it gives up the instant permit, adds a building permit and needs an engineer's sign-off. Layout A keeps the simpler route, provided the address clears the historic and flood checks.
The fee range reflects something the procedure doesn't say: whether the $15 applies per started $1,000 or pro rata. If B's two permits each carry a first-$1,000 charge, its fee rises a little more.
The Buy-All row is a year-1 payment for production before shade, not savings. You still buy the electricity you use, and shade will lower both figures.
Check the solar-only price per watt against the state benchmark
An East Hartford quote file can carry three different per-watt numbers. The permit application uses the town's $3.50/W valuation, explained in the next section. The quote has a total price per watt. Only the third, the solar-only price per watt, belongs next to a market benchmark.
Work it out in three steps.
- Find the DC size. Multiply the panel count by the panel's rated watts. Twenty-four 400 W panels make 9,600 W.
- Take out what isn't the solar array. Subtract any itemized structural reinforcement, roof replacement, battery or main-panel upgrade line. In East Hartford the reinforcement line matters twice: it moves a layout off SolarAPP+, and it inflates the total price per watt.
- Divide and compare. Divide the solar-only price by the DC watts. Then compare it with the state benchmark.
State benchmark: EcoGen's Solar Cost Index puts Connecticut at $2.80 per watt, a modeled installed price before incentives (September 2026 edition, prices as of September 25, 2026). EcoGen calls it a state cost benchmark, not a quote for your home. Its Connecticut cost page gives a typical quote band of $2.46 to $3.14 per watt and the 1,294 kWh per kW per year production reference used in the example above. The figures are statewide and solar only, not an East Hartford price. If EcoGen publishes a newer edition, use that one.
Now read the result. Inside the band is not proof of a fair price, and outside it is not proof of a bad one. A figure above $3.14 is a reason to ask what's driving it: equipment, a difficult roof, or a line that should have been itemized. A figure below $2.46 is a reason to check what is excluded.
Leave the federal tax credit out of the comparison. One online cost guide for East Hartford, dated January 2025 and still online in mid-2026, gives its price "with the federal tax credit". That credit is gone for systems you buy: the IRS says the Residential Clean Energy Credit (25D) is not allowed for expenditures made after December 31, 2025. If a quote shows a "net price after the federal credit" for a system you would own, ask for the price with no credit in it. This is not tax advice.
The town's $3.50 per watt is a fee basis, not a price
The town's procedure says: "Projects should be valued at $3.50/W." It is the valuation East Hartford uses to calculate the permit fee, not an approved price or a market benchmark. It also sits well above EcoGen's $2.80 state figure, so a quote near $3.50 is not "the town's price".
The fee is $30 for the first $1,000 of valuation plus $15 for each $1,000 after that. Because the valuation runs off watts, a bigger array raises the fee whatever the contract price. When both permits are needed, the procedure says project costs should be split between building and electrical work.
Illustrative calculation: a 6.4 kW layout is valued at $22,400, for a fee of about $351–$360. A 9.6 kW layout is valued at $33,600, for about $519–$525, whether the installer charges $25,000 or $35,000. The ranges cover the unresolved rounding question.
Confirm three things with the department: how it rounds, whether a SolarAPP+ submission uses the same valuation, and whether any state fee is added. Then check that the quote names the fee and who pays it.
Eversource pays more here: the 2026 tariff and the town adder
East Hartford is on the 2025 Distressed Municipalities list from the Connecticut Department of Economic and Community Development (DECD), ranked third. The state's residential solar program pays an extra amount per kWh for systems in towns on the current list, so get the adder on each layout's sheet.
The program is RRES, the Residential Renewable Energy Solutions program overseen by the Public Utilities Regulatory Authority (PURA). East Hartford is Eversource territory. You choose one of two tariffs, and the choice holds for 20 years. RRES covers 1–4 family homes, with systems up to 25 kW.
Eversource's 2026 rates, for applications submitted in 2026:
| 2026 RRES | Buy-All | Netting |
|---|---|---|
| How it works | Eversource buys all the system's production at a fixed rate. You keep buying the power you use. | Production you use offsets your purchases. Exports earn bill credits at the retail rate, and credits roll over. |
| Base rate | $0.3289 per kWh | $0.000 per kWh incentive payment |
| Distressed-municipality adder | +$0.0275 per kWh | +$0.0175 per kWh |
| Charge on production | None | Solar Energy Adjustment (SEA) of $0.0402 per kWh on all production, shown on the bill |
| Can you switch later? | No | No |
The Solar Energy Adjustment is charged on everything the system produces, not just exports. In the worked example, that is about $333 a year for Layout A and $499 for Layout B (illustrative calculation, before shade).
The adder belongs to the municipality where the system sits. The utilities' 2026 program update says projects qualify when they are located in "a current Distressed Municipality on the DECD website". It also warns that many bills show a neighborhood or village name instead. DECD updates the list every year, so ask Eversource to confirm the adder for your address at application.
Keep two limits in mind. These are 2026 rates. No 2027 decision had been posted when this page was checked, and the state has started work on a successor program, so a 2027 applicant should ask for the rate in force on the application date. The tariff choice is also permanent, so see both options for both layouts before you decide.
Inspection day and the handoff to Eversource
The town's procedure spells out who must be present and what happens after the system passes. In order:
- Lock the layout before work starts. On SolarAPP+, a change order needs a new Approval ID.
- Install, then book the inspection. The inspection is scheduled by phone after the work is finished, with 24 hours' notice.
- Be there. A roof mount gets one on-site inspection, and the procedure says the homeowner and the electrician must both be present. The inspector arrives within a one-hour window.
- The town notifies Eversource. "Once the system has passed inspection the Building Department will notify Eversource within one business day."
- Utility connection. Only a licensed E-1 or E-2 electrician may connect the system to your existing electrical system or meter. A PV-only solar licence does not allow it.
Ask who books the inspection, who attends and who files the Eversource application. Your Buy-All or Netting choice is made at interconnection, so settle it before step 4.
Questions to ask before you sign in East Hartford
Take this list to every quote meeting. The quote checklist on this site follows the same order.
- Permit route per layout. SolarAPP+ or individual review? If SolarAPP+, will I get the Approval ID? If not, which exclusion applies?
- Historic district and flood check. What did you find for my parcel, and from which source: the town's GIS viewer, FEMA's map or the Grants Manager?
- Reinforcement. If a layout needs it, where is the engineer's note, and is the work priced as its own line? Is the building permit in the scope?
- Licences on the permit. Whose E-1 licence and HIC registration go on the application? Ask for the numbers so you can check them with the Department of Consumer Protection. Under its solar licence rules, only an E-1 or E-2 holder may connect the system to your wiring or meter.
- Inspection attendance. Which electrician will attend, and who books the slot?
- Permit fee. Is it in the price, and did you calculate it at the town's $3.50/W valuation for both permits?
- Tariff estimate. Show Buy-All and Netting for each layout, with the distressed-municipality adder as a separate line. Which year's rates did you use?
- Eversource fees. Are the application and meter fees included in the quote, or billed separately?
- Price per watt. What is the solar-only price per watt, with reinforcement, roof and panel-upgrade work removed? Does any figure assume a federal tax credit?
- Shade. What shade loss did you assume on each roof face, and how was it measured?
- Change orders. If the layout changes after approval, who handles the new Approval ID or the amended plans, and does the price change?
How to use the answers: put the two layouts side by side. Strike out any quote that cannot name its permit route or its solar-only price per watt. Then compare what is left on route, production and price, in that order.
Short answers for East Hartford homeowners
Why will I still get an Eversource bill with solar?
Both 2026 tariffs keep a bill. On Buy-All, you still buy all the electricity you use; the production payment, including East Hartford's $0.0275 adder, is separate. On Netting, credits offset what you use, but the $0.0402 per kWh Solar Energy Adjustment on all production shows on the bill.
What happens if the layout changes after the permit?
On SolarAPP+, a changed design needs a new Approval ID. SolarAPP+ allows three free changes, and the town doesn't charge for amended plans. A change that adds reinforcement takes the project off SolarAPP+ and into individual review with a building permit.
Does this apply to a three-family house?
Partly. East Hartford's SolarAPP+ route and its 1–2 family application cover one- and two-family homes only; larger homes use a separate application. RRES still covers 1–4 family properties, so a three- or four-family home can still choose Buy-All or Netting.
